"H" Extension for Hypervisor Support, Version 1.0

This chapter describes the RISC-V hypervisor extension, which virtualizes the supervisor-level architecture to support the efficient hosting of guest operating systems atop a type-1 or type-2 hypervisor. The hypervisor extension changes supervisor mode into hypervisor-extended supervisor mode (HS-mode, or hypervisor mode for short), where a hypervisor or a hosting-capable operating system runs. The hypervisor extension also adds another stage of address translation, from guest physical addresses to supervisor physical addresses, to virtualize the memory and memory-mapped I/O subsystems for a guest operating system. HS-mode acts the same as S-mode, but with additional instructions and CSRs that control the new stage of address translation and support hosting a guest OS in virtual S-mode (VS-mode). Regular S-mode operating systems can execute without modification either in HS-mode or as VS-mode guests.

In HS-mode, an OS or hypervisor interacts with the machine through the same SBI as an OS normally does from S-mode. An HS-mode hypervisor is expected to implement the SBI for its VS-mode guest.

The hypervisor extension depends on an "I" base integer ISA with 32 x registers (RV32I or RV64I), not RV32E or RV64E, which have only 16 x registers. CSR mtval must not be read-only zero, and standard page-based address translation must be supported, either Sv32 for RV32, or a minimum of Sv39 for RV64.

The hypervisor extension is enabled by setting bit 7 in the misa CSR, which corresponds to the letter H. RISC-V harts that implement the hypervisor extension are encouraged not to hardwire misa[7], so that the extension may be disabled.

The baseline privileged architecture is designed to simplify the use of classic virtualization techniques, where a guest OS is run at user-level, as the few privileged instructions can be easily detected and trapped. The hypervisor extension improves virtualization performance by reducing the frequency of these traps.

The hypervisor extension has been designed to be efficiently emulable on platforms that do not implement the extension, by running the hypervisor in S-mode and trapping into M-mode for hypervisor CSR accesses and to maintain shadow page tables. The majority of CSR accesses for type-2 hypervisors are valid S-mode accesses so need not be trapped. Hypervisors can support nested virtualization analogously.

Privilege Modes

The current virtualization mode, denoted V, indicates whether the hart is currently executing in a guest. When V=1, the hart is either in virtual S-mode (VS-mode), or in virtual U-mode (VU-mode) atop a guest OS running in VS-mode. When V=0, the hart is either in M-mode, in HS-mode, or in U-mode atop an OS running in HS-mode. The virtualization mode also indicates whether two-stage address translation is active (V=1) or inactive (V=0). Privilege modes with the hypervisor extension. lists the possible privilege modes of a RISC-V hart with the hypervisor extension.

Table 1. Privilege modes with the hypervisor extension.

Virtualization
Mode (V)

Nominal Privilege

Abbreviation

Name

Two-Stage Translation

0
0
0

U
S
M

U-mode
HS-mode
M-mode

User mode
Hypervisor-extended supervisor mode
Machine mode

Off
Off
Off

1
1

U
S

VU-mode
VS-mode

Virtual user mode
Virtual supervisor mode

On
On

For privilege modes U and VU, the nominal privilege mode is U, and for privilege modes HS and VS, the nominal privilege mode is S.

HS-mode is more privileged than VS-mode, and VS-mode is more privileged than VU-mode. VS-mode interrupts are globally disabled when executing in U-mode.

This description does not consider the possibility of U-mode or VU-mode interrupts and will be revised if an extension for user-level interrupts is adopted.

Hypervisor and Virtual Supervisor CSRs

An OS or hypervisor running in HS-mode uses the supervisor CSRs to interact with the exception, interrupt, and address-translation subsystems. Additional CSRs are provided to HS-mode, but not to VS-mode, to manage two-stage address translation and to control the behavior of a VS-mode guest: hstatus, hedeleg, hideleg, hvip, hip, hie, hgeip, hgeie, henvcfg, henvcfgh, hcounteren, htimedelta, htimedeltah, htval, htinst, and hgatp.

Furthermore, several virtual supervisor CSRs (VS CSRs) are replicas of the normal supervisor CSRs. For example, vsstatus is the VS CSR that duplicates the usual sstatus CSR.

When V=1, the VS CSRs substitute for the corresponding supervisor CSRs, taking over all functions of the usual supervisor CSRs except as specified otherwise. Instructions that normally read or modify a supervisor CSR shall instead access the corresponding VS CSR. When V=1, an attempt to read or write a VS CSR directly by its own separate CSR address causes a virtual-instruction exception. (Attempts from U-mode cause an illegal-instruction exception as usual.) The VS CSRs can be accessed as themselves only from M-mode or HS-mode.

While V=1, the normal HS-level supervisor CSRs that are replaced by VS CSRs retain their values but do not affect the behavior of the machine unless specifically documented to do so. Conversely, when V=0, the VS CSRs do not ordinarily affect the behavior of the machine other than being readable and writable by CSR instructions.

Some standard supervisor CSRs (senvcfg, scounteren, and scontext, possibly others) have no matching VS CSR. These supervisor CSRs continue to have their usual function and accessibility even when V=1, except with VS-mode and VU-mode substituting for HS-mode and U-mode. Hypervisor software is expected to manually swap the contents of these registers as needed.

Matching VS CSRs exist only for the supervisor CSRs that must be duplicated, which are mainly those that get automatically written by traps or that impact instruction execution immediately after trap entry and/or right before SRET, when software alone is unable to swap a CSR at exactly the right moment. Currently, most supervisor CSRs fall into this category, but future ones might not.

In this chapter, we use the term HSXLEN to refer to the effective XLEN when executing in HS-mode, and VSXLEN to refer to the effective XLEN when executing in VS-mode.

Hypervisor Status Register (hstatus)

The hstatus register is an HSXLEN-bit read/write register formatted as shown in Hypervisor status register (hstatus) when HSLEN=32 when HSXLEN=32 and Hypervisor status register (hstatus) when HSXLEN=64. when HSXLEN=64. The hstatus register provides facilities analogous to the mstatus register for tracking and controlling the exception behavior of a VS-mode guest.

Hypervisor status register (hstatus) when HSLEN=32

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hstatusreg-rv32.edn[]

Hypervisor status register (hstatus) when HSXLEN=64.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hstatusreg.edn[]

The VSXL field controls the effective XLEN for VS-mode (known as VSXLEN), which may differ from the XLEN for HS-mode (HSXLEN). When HSXLEN=32, the VSXL field does not exist, and VSXLEN=32. When HSXLEN=64, VSXL is a WARL field that is encoded the same as the MXL field of misa, shown in [misabase] on page 19. In particular, an implementation may make VSXL be a read-only field whose value always ensures that VSXLEN=HSXLEN.

If HSXLEN is changed from 32 to a wider width, and if field VSXL is not restricted to a single value, it gets the value corresponding to the widest supported width not wider than the new HSXLEN.

The hstatus fields VTSR, VTW, and VTVM are defined analogously to the mstatus fields TSR, TW, and TVM, but affect execution only in VS-mode, and cause virtual-instruction exceptions instead of illegal-instruction exceptions. When VTSR=1, an attempt in VS-mode to execute SRET raises a virtual-instruction exception. When VTW=1 (and assuming mstatus.TW=0), an attempt in VS-mode to execute WFI raises a virtual-instruction exception if the WFI does not complete within an implementation-specific, bounded time limit. An implementation may have WFI always raise a virtual-instruction exception in VS-mode when VTW=1 (and mstatus.TW=0), even if there are pending globally-disabled interrupts when the instruction is executed. When VTVM=1, an attempt in VS-mode to execute SFENCE.VMA or SINVAL.VMA or to access CSR satp raises a virtual-instruction exception.

The VGEIN (Virtual Guest External Interrupt Number) field selects a guest external interrupt source for VS-level external interrupts. VGEIN is a WLRL field that must be able to hold values between zero and the maximum guest external interrupt number (known as GEILEN), inclusive. When VGEIN=0, no guest external interrupt source is selected for VS-level external interrupts. GEILEN may be zero, in which case VGEIN may be read-only zero. Guest external interrupts are explained in Hypervisor Guest External Interrupt Registers (hgeip and hgeie), and the use of VGEIN is covered further in Hypervisor Interrupt Registers (hvip, hip, and hie).

Field HU (Hypervisor in U-mode) controls whether the virtual-machine load/store instructions, HLV, HLVX, and HSV, can be used also in U-mode. When HU=1, these instructions can be executed in U-mode the same as in HS-mode. When HU=0, all hypervisor instructions cause an illegal-instruction exception in U-mode.

The HU bit allows a portion of a hypervisor to be run in U-mode for greater protection against software bugs, while still retaining access to a virtual machine’s memory.

The SPV bit (Supervisor Previous Virtualization mode) is written by the implementation whenever a trap is taken into HS-mode. Just as the SPP bit in sstatus is set to the (nominal) privilege mode at the time of the trap, the SPV bit in hstatus is set to the value of the virtualization mode V at the time of the trap. When an SRET instruction is executed when V=0, V is set to SPV.

When V=1 and a trap is taken into HS-mode, bit SPVP (Supervisor Previous Virtual Privilege) is set to the nominal privilege mode at the time of the trap, the same as sstatus.SPP. But if V=0 before a trap, SPVP is left unchanged on trap entry. SPVP controls the effective privilege of explicit memory accesses made by the virtual-machine load/store instructions, HLV, HLVX, and HSV.

Without SPVP, if instructions HLV, HLVX, and HSV looked instead to sstatus.SPP for the effective privilege of their memory accesses, then, even with HU=1, U-mode could not access virtual machine memory at VS-level, because to enter U-mode using SRET always leaves SPP=0. Unlike SPP, field SPVP is untouched by transitions back-and-forth between HS-mode and U-mode.

Field GVA (Guest Virtual Address) is written by the implementation whenever a trap is taken into HS-mode. For any trap (breakpoint, address misaligned, access fault, page fault, or guest-page fault) that writes a guest virtual address to stval, GVA is set to 1. For any other trap into HS-mode, GVA is set to 0.

For breakpoint and memory access traps that write a nonzero value to stval, GVA is redundant with field SPV (the two bits are set the same) except when the explicit memory access of an HLV, HLVX, or HSV instruction causes a fault. In that case, SPV=0 but GVA=1.

The VSBE bit is a WARL field that controls the endianness of explicit memory accesses made from VS-mode. If VSBE=0, explicit load and store memory accesses made from VS-mode are little-endian, and if VSBE=1, they are big-endian. VSBE also controls the endianness of all implicit accesses to VS-level memory management data structures, such as page tables. An implementation may make VSBE a read-only field that always specifies the same endianness as HS-mode.

Hypervisor Trap Delegation Registers (hedeleg and hideleg)

Register hedeleg is a 64-bit read/write register, formatted as shown in Hypervisor exception delegation register (hedeleg).. Register hideleg is an HSXLEN-bit read/write register, formatted as shown in Hypervisor exception delegation register (hideleg).. By default, all traps at any privilege level are handled in M-mode, though M-mode usually uses the medeleg and mideleg CSRs to delegate some traps to HS-mode. The hedeleg and hideleg CSRs allow these traps to be further delegated to a VS-mode guest; their layout is the same as medeleg and mideleg.

Hypervisor exception delegation register (hedeleg).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hedelegreg.edn[]

Hypervisor exception delegation register (hideleg).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hidelegreg.edn[]

A synchronous trap that has been delegated to HS-mode (using medeleg) is further delegated to VS-mode if V=1 before the trap and the corresponding hedeleg bit is set. Each bit of hedeleg shall be either writable or read-only zero. Many bits of hedeleg are required specifically to be writable or zero, as enumerated in Bits of hedeleg that must be writable or must be read-only zero.. Bit 0, corresponding to instruction address misaligned exceptions, must be writable if IALIGN=32.

Requiring that certain bits of hedeleg be writable reduces some of the burden on a hypervisor to handle variations of implementation.

When XLEN=32, hedelegh is a 32-bit read/write register that aliases bits 63:32 of hedeleg. Register hedelegh does not exist when XLEN=64.

An interrupt that has been delegated to HS-mode (using mideleg) is further delegated to VS-mode if the corresponding hideleg bit is set. Among bits 15:0 of hideleg, bits 10, 6, and 2 (corresponding to the standard VS-level interrupts) are writable, and bits 12, 9, 5, and 1 (corresponding to the standard S-level interrupts) are read-only zeros.

When a virtual supervisor external interrupt (code 10) is delegated to VS-mode, it is automatically translated by the machine into a supervisor external interrupt (code 9) for VS-mode, including the value written to vscause on an interrupt trap. Likewise, a virtual supervisor timer interrupt (6) is translated into a supervisor timer interrupt (5) for VS-mode, and a virtual supervisor software interrupt (2) is translated into a supervisor software interrupt (1) for VS-mode. Similar translations may or may not be done for platform interrupt causes (codes 16 and above).

Table 2. Bits of hedeleg that must be writable or must be read-only zero.
Bit Attribute Corresponding Exception

0
1
2
3
4
5
6
7
8
9
10
11
12
13
15
18
19
20
21
22
23

(See text)
Writable
Writable
Writable
Writable
Writable
Writable
Writable
Writable
Read-only 0
Read-only 0
Read-only 0
Writable
Writable
Writable
Writable
Writable
Read-only 0
Read-only 0
Read-only 0
Read-only 0

Instruction address misaligned
Instruction access fault
Illegal instruction
Breakpoint
Load address misaligned
Load access fault
Store/AMO address misaligned
Store/AMO access fault
Environment call from U-mode or VU-mode
Environment call from HS-mode
Environment call from VS-mode
Environment call from M-mode
Instruction page fault
Load page fault
Store/AMO page fault
Software check
Hardware error
Instruction guest-page fault
Load guest-page fault
Virtual instruction
Store/AMO guest-page fault

Hypervisor Interrupt Registers (hvip, hip, and hie)

Register hvip is an HSXLEN-bit read/write register that a hypervisor can write to indicate virtual interrupts intended for VS-mode. Bits of hvip that are not writable are read-only zeros.

Hypervisor virtual-interrupt-pending register(hvip).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hvipreg.edn[]

The standard portion (bits 15:0) of hvip is formatted as shown in Standard portion (bits 15:0) of hvip.. Bits VSEIP, VSTIP, and VSSIP of hvip are writable. Setting VSEIP=1 in hvip asserts a VS-level external interrupt; setting VSTIP asserts a VS-level timer interrupt; and setting VSSIP asserts a VS-level software interrupt.

Standard portion (bits 15:0) of hvip.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hvipreg-standard.edn[]

Registers hip and hie are HSXLEN-bit read/write registers that supplement HS-level’s sip and sie respectively. The hip register indicates pending VS-level and hypervisor-specific interrupts, while hie contains enable bits for the same interrupts.

Hypervisor interrupt-pending register (hip).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hipreg.edn[]

Hypervisor interrupt-enable register (hie).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hiereg.edn[]

For each writable bit in sie, the corresponding bit shall be read-only zero in both hip and hie. Hence, the nonzero bits in sie and hie are always mutually exclusive, and likewise for sip and hip.

The active bits of hip and hie cannot be placed in HS-level’s sip and sie because doing so would make it impossible for software to emulate the hypervisor extension on platforms that do not implement it in hardware.

An interrupt i will trap to HS-mode whenever all of the following are true: (a) either the current operating mode is HS-mode and the SIE bit in the sstatus register is set, or the current operating mode has less privilege than HS-mode; (b) bit i is set in both sip and sie, or in both hip and hie; and (c) bit i is not set in hideleg.

If bit i of sie is read-only zero, the same bit in register hip may be writable or may be read-only. When bit i in hip is writable, a pending interrupt i can be cleared by writing 0 to this bit. If interrupt i can become pending in hip but bit i in hip is read-only, then either the interrupt can be cleared by clearing bit i of hvip, or the implementation must provide some other mechanism for clearing the pending interrupt (which may involve a call to the execution environment).

A bit in hie shall be writable if the corresponding interrupt can ever become pending in hip. Bits of hie that are not writable shall be read-only zero.

The standard portions (bits 15:0) of registers hip and hie are formatted as shown in Standard portion (bits 15:0) of hip. and Standard portion (bits 15:0) of hie. respectively.

Standard portion (bits 15:0) of hip.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hipreg-standard.edn[]

Standard portion (bits 15:0) of hie.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hiereg-standard.edn[]

Bits hip.SGEIP and hie.SGEIE are the interrupt-pending and interrupt-enable bits for guest external interrupts at supervisor level (HS-level). SGEIP is read-only in hip, and is 1 if and only if the bitwise logical-AND of CSRs hgeip and hgeie is nonzero in any bit. (See Hypervisor Guest External Interrupt Registers (hgeip and hgeie).)

Bits hip.VSEIP and hie.VSEIE are the interrupt-pending and interrupt-enable bits for VS-level external interrupts. VSEIP is read-only in hip, and is the logical-OR of these interrupt sources:

  • bit VSEIP of hvip;

  • the bit of hgeip selected by hstatus.VGEIN; and

  • any other platform-specific external interrupt signal directed to VS-level.

Bits hip.VSTIP and hie.VSTIE are the interrupt-pending and interrupt-enable bits for VS-level timer interrupts. VSTIP is read-only in hip, and is the logical-OR of hvip.VSTIP and any other platform-specific timer interrupt signal directed to VS-level.

Bits hip.VSSIP and hie.VSSIE are the interrupt-pending and interrupt-enable bits for VS-level software interrupts. VSSIP in hip is an alias (writable) of the same bit in hvip.

Multiple simultaneous interrupts destined for HS-mode are handled in the following decreasing priority order: SEI, SSI, STI, SGEI, VSEI, VSSI, VSTI.

Hypervisor Guest External Interrupt Registers (hgeip and hgeie)

The hgeip register is an HSXLEN-bit read-only register, formatted as shown in Hypervisor guest external interrupt-pending register (hgeip)., that indicates pending guest external interrupts for this hart. The hgeie register is an HSXLEN-bit read/write register, formatted as shown in Hypervisor guest external interrupt-enable register (hgeie)., that contains enable bits for the guest external interrupts at this hart. Guest external interrupt number i corresponds with bit i in both hgeip and hgeie.

Hypervisor guest external interrupt-pending register (hgeip).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hgeipreg.edn[]

Hypervisor guest external interrupt-enable register (hgeie).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hgeiereg.edn[]

Guest external interrupts represent interrupts directed to individual virtual machines at VS-level. If a RISC-V platform supports placing a physical device under the direct control of a guest OS with minimal hypervisor intervention (known as pass-through or direct assignment between a virtual machine and the physical device), then, in such circumstance, interrupts from the device are intended for a specific virtual machine. Each bit of hgeip summarizes all pending interrupts directed to one virtual hart, as collected and reported by an interrupt controller. To distinguish specific pending interrupts from multiple devices, software must query the interrupt controller.

Support for guest external interrupts requires an interrupt controller that can collect virtual-machine-directed interrupts separately from other interrupts.

The number of bits implemented in hgeip and hgeie for guest external interrupts is UNSPECIFIED and may be zero. This number is known as GEILEN. The least-significant bits are implemented first, apart from bit 0. Hence, if GEILEN is nonzero, bits GEILEN:1 shall be writable in hgeie, and all other bit positions shall be read-only zeros in both hgeip and hgeie.

The set of guest external interrupts received and handled at one physical hart may differ from those received at other harts. Guest external interrupt number i at one physical hart is typically expected not to be the same as guest external interrupt i at any other hart. For any one physical hart, the maximum number of virtual harts that may directly receive guest external interrupts is limited by GEILEN. The maximum this number can be for any implementation is 31 for RV32 and 63 for RV64, per physical hart.

A hypervisor is always free to emulate devices for any number of virtual harts without being limited by GEILEN. Only direct pass-through (direct assignment) of interrupts is affected by the GEILEN limit, and the limit is on the number of virtual harts receiving such interrupts, not the number of distinct interrupts received. The number of distinct interrupts a single virtual hart may receive is determined by the interrupt controller.

Register hgeie selects the subset of guest external interrupts that cause a supervisor-level (HS-level) guest external interrupt. The enable bits in hgeie do not affect the VS-level external interrupt signal selected from hgeip by hstatus.VGEIN.

Hypervisor Environment Configuration Register (henvcfg)

The henvcfg CSR is a 64-bit read/write register, formatted as shown in Hypervisor environment configuration register (henvcfg)., that controls certain characteristics of the execution environment when virtualization mode V=1.

Hypervisor environment configuration register (henvcfg).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/henvcfg.edn[]

If bit FIOM (Fence of I/O implies Memory) is set to one in henvcfg, FENCE instructions executed when V=1 are modified so the requirement to order accesses to device I/O implies also the requirement to order main memory accesses. Modified interpretation of FENCE predecessor and successor sets when FIOM=1 and virtualization mode V=1. details the modified interpretation of FENCE instruction bits PI, PO, SI, and SO when FIOM=1 and V=1.

Similarly, when FIOM=1 and V=1, if an atomic instruction that accesses a region ordered as device I/O has its aq and/or rl bit set, then that instruction is ordered as though it accesses both device I/O and memory.

Table 3. Modified interpretation of FENCE predecessor and successor sets when FIOM=1 and virtualization mode V=1.
Instruction bit Meaning when set

PI
PO

Predecessor device input and memory reads (PR implied)
Predecessor device output and memory writes (PW implied)

SI
SO

Successor device input and memory reads (SR implied)
Successor device output and memory writes (SW implied)

The PBMTE bit controls whether the Svpbmt extension is available for use in VS-stage address translation. When PBMTE=1, Svpbmt is available for VS-stage address translation. When PBMTE=0, the implementation behaves as though Svpbmt were not implemented for VS-stage address translation. If Svpbmt is not implemented, PBMTE is read-only zero.

If the Svadu extension is implemented, the ADUE bit controls whether hardware updating of PTE A/D bits is enabled for VS-stage address translation. When ADUE=1, hardware updating of PTE A/D bits is enabled during VS-stage address translation, and the implementation behaves as though the Svade extension were not implemented for VS-mode address translation. When ADUE=0, the implementation behaves as though Svade were implemented for VS-stage address translation. If Svadu is not implemented, ADUE is read-only zero.

The definition of the STCE field will be furnished by the forthcoming Sstc extension. Its allocation within henvcfg may change prior to the

The definition of the CBZE field will be furnished by the forthcoming Zicboz extension. Its allocation within henvcfg may change prior to the ratification of that extension.

The definitions of the CBCFE and CBIE fields will be furnished by the forthcoming Zicbom extension. Their allocations within henvcfg may change prior to the ratification of that extension.

The definition of the PMM field will be furnished by the forthcoming Ssnpm extension. Its allocation within henvcfg may change prior to the ratification of that extension.

When XLEN=32, henvcfgh is a 32-bit read/write register that aliases bits 63:32 of henvcfg. Register henvcfgh does not exist when XLEN=64.

Hypervisor Counter-Enable Register (hcounteren)

The counter-enable register hcounteren is a 32-bit register that controls the availability of the hardware performance monitoring counters to the guest virtual machine.

Hypervisor counter-enable register (hcounteren).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hcounterenreg.edn[]

When the CY, TM, IR, or HPM_n_ bit in the hcounteren register is clear, attempts to read the cycle, time, instret, or hpmcounter n register while V=1 will cause a virtual-instruction exception if the same bit in mcounteren is 1. When one of these bits is set, access to the corresponding register is permitted when V=1, unless prevented for some other reason. In VU-mode, a counter is not readable unless the applicable bits are set in both hcounteren and scounteren.

hcounteren must be implemented. However, any of the bits may be read-only zero, indicating reads to the corresponding counter will cause an exception when V=1. Hence, they are effectively WARL fields.

Hypervisor Time Delta Register (htimedelta)

The htimedelta CSR is a 64-bit read/write register that contains the delta between the value of the time CSR and the value returned in VS-mode or VU-mode. That is, reading the time CSR in VS or VU mode returns the sum of the contents of htimedelta and the actual value of time.

Because overflow is ignored when summing htimedelta and time, large values of htimedelta may be used to represent negative time offsets.

Hypervisor time delta register.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/htimedelta.edn[]

When XLEN=32, htimedeltah is a 32-bit read/write register that aliases bits 63:32 of htimedelta. Register htimedeltah does not exist when XLEN=64.

Hypervisor Trap Value Register (htval)

The htval register is an HSXLEN-bit read/write register formatted as shown in Hypervisor trap value register (htval).. When a trap is taken into HS-mode, htval is written with additional exception-specific information, alongside stval, to assist software in handling the trap.

Hypervisor trap value register (htval).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/htvalreg.edn[]

When a guest-page-fault trap is taken into HS-mode, htval is written with either zero or the guest physical address that faulted, shifted right by 2 bits. For other traps, htval is set to zero, but a future standard or extension may redefine htval’s setting for other traps.

A guest-page fault may arise due to an implicit memory access during first-stage (VS-stage) address translation, in which case a guest physical address written to htval is that of the implicit memory access that faulted—for example, the address of a VS-level page table entry that could not be read. (The guest physical address corresponding to the original virtual address is unknown when VS-stage translation fails to complete.) Additional information is provided in CSR htinst to disambiguate such situations.

Otherwise, for misaligned loads and stores that cause guest-page faults, a nonzero guest physical address in htval corresponds to the faulting portion of the access as indicated by the virtual address in stval. For instruction guest-page faults on systems with variable-length instructions, a nonzero htval corresponds to the faulting portion of the instruction as indicated by the virtual address in stval.

A guest physical address written to htval is shifted right by 2 bits to accommodate addresses wider than the current XLEN. For RV32, the hypervisor extension permits guest physical addresses as wide as 34 bits, and htval reports bits 33:2 of the address. This shift-by-2 encoding of guest physical addresses matches the encoding of physical addresses in PMP address registers ([pmp]) and in page table entries ([sv32], [sv39], [sv48], and [sv57]).

If the least-significant two bits of a faulting guest physical address are needed, these bits are ordinarily the same as the least-significant two bits of the faulting virtual address in stval. For faults due to implicit memory accesses for VS-stage address translation, the least-significant two bits are instead zeros. These cases can be distinguished using the value provided in register htinst.

htval is a WARL register that must be able to hold zero and may be capable of holding only an arbitrary subset of other 2-bit-shifted guest physical addresses, if any.

Unless it has reason to assume otherwise (such as a platform standard), software that writes a value to htval should read back from htval to confirm the stored value.

Hypervisor Trap Instruction Register (htinst)

The htinst register is an HSXLEN-bit read/write register formatted as shown in Hypervisor trap instruction register (htinst).. When a trap is taken into HS-mode, htinst is written with a value that, if nonzero, provides information about the instruction that trapped, to assist software in handling the trap. The values that may be written to htinst on a trap are documented in Transformed Instruction or Pseudoinstruction for mtinst or htinst.

Hypervisor trap instruction register (htinst).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/htinstreg.edn[]

htinst is a WARL register that need only be able to hold the values that the implementation may automatically write to it on a trap.

Hypervisor Guest Address Translation and Protection Register (hgatp)

The hgatp register is an HSXLEN-bit read/write register, formatted as shown in Hypervisor guest address translation and protection register hgatp when HSXLEN=32. for HSXLEN=32 and Hypervisor guest address translation and protection register hgatp when HSXLEN=64 for MODE values Bare, Sv39x4, and Sv57x4. for HSXLEN=64, which controls G-stage address translation and protection, the second stage of two-stage translation for guest virtual addresses (see Two-Stage Address Translation). Similar to CSR satp, this register holds the physical page number (PPN) of the guest-physical root page table; a virtual machine identifier (VMID), which facilitates address-translation fences on a per-virtual-machine basis; and the MODE field, which selects the address-translation scheme for guest physical addresses. When mstatus.TVM=1, attempts to read or write hgatp while executing in HS-mode will raise an illegal-instruction exception.

Hypervisor guest address translation and protection register hgatp when HSXLEN=32.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/rv32hgatp.edn[]

Hypervisor guest address translation and protection register hgatp when HSXLEN=64 for MODE values Bare, Sv39x4, and Sv57x4.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/rv64hgatp.edn[]

Encoding of hgatp MODE field. shows the encodings of the MODE field when HSXLEN=32 and HSXLEN=64. When MODE=Bare, guest physical addresses are equal to supervisor physical addresses, and there is no further memory protection for a guest virtual machine beyond the physical memory protection scheme described in [pmp]. In this case, the remaining fields in hgatp must be set to zeros.

When HSXLEN=32, the only other valid setting for MODE is Sv32x4, which is a modification of the usual Sv32 paged virtual-memory scheme, extended to support 34-bit guest physical addresses. When HSXLEN=64, modes Sv39x4, Sv48x4, and Sv57x4 are defined as modifications of the Sv39, Sv48, and Sv57 paged virtual-memory schemes. All of these paged virtual-memory schemes are described in Guest Physical Address Translation.

The remaining MODE settings when HSXLEN=64 are reserved for future use and may define different interpretations of the other fields in hgatp.

Table 4. Encoding of hgatp MODE field.
HSXLEN=32

Value

Name

Description

0
1

Bare
Sv32x4

No translation or protection.
Page-based 34-bit virtual addressing (2-bit extension of Sv32).

HSXLEN=64

Value

Name

Description

0
1-7
8
9
10
11-15

Bare

Sv39x4
Sv48x4
Sv57x4

No translation or protection.
Reserved
Page-based 41-bit virtual addressing (2-bit extension of Sv39).
Page-based 50-bit virtual addressing (2-bit extension of Sv48).
Page-based 59-bit virtual addressing (2-bit extension of Sv57).
Reserved

Implementations are not required to support all defined MODE settings when HSXLEN=64.

A write to hgatp with an unsupported MODE value is not ignored as it is for satp. Instead, the fields of hgatp are WARL in the normal way, when so indicated.

As explained in Guest Physical Address Translation, for the paged virtual-memory schemes (Sv32x4, Sv39x4, Sv48x4, and Sv57x4), the root page table is 16 KiB and must be aligned to a 16-KiB boundary. In these modes, the lowest two bits of the physical page number (PPN) in hgatp always read as zeros. An implementation that supports only the defined paged virtual-memory schemes and/or Bare may make PPN[1:0] read-only zero.

The number of VMID bits is UNSPECIFIED and may be zero. The number of implemented VMID bits, termed VMIDLEN, may be determined by writing one to every bit position in the VMID field, then reading back the value in hgatp to see which bit positions in the VMID field hold a one. The least-significant bits of VMID are implemented first: that is, if VMIDLEN > 0, VMID[VMIDLEN-1:0] is writable. The maximal value of VMIDLEN, termed VMIDMAX, is 7 for Sv32x4 or 14 for Sv39x4, Sv48x4, and Sv57x4.

The hgatp register is considered active for the purposes of the address-translation algorithm unless the effective privilege mode is U and hstatus.HU=0.

This definition simplifies the implementation of speculative execution of HLV, HLVX, and HSV instructions.

Note that writing hgatp does not imply any ordering constraints between page-table updates and subsequent G-stage address translations. If the new virtual machine’s guest physical page tables have been modified, or if a VMID is reused, it may be necessary to execute an HFENCE.GVMA instruction (see Hypervisor Memory-Management Fence Instructions) before or after writing hgatp.

Virtual Supervisor Status Register (vsstatus)

The vsstatus register is a VSXLEN-bit read/write register that is VS-mode’s version of supervisor register sstatus, formatted as shown in Virtual supervisor status register (vstatus) when VSXLEN=32. when VSXLEN=32 and Virtual supervisor status register (vsstatus) when VSXLEN=64. when VSXLEN=64. When V=1, vsstatus substitutes for the usual sstatus, so instructions that normally read or modify sstatus actually access vsstatus instead.

Virtual supervisor status register (vstatus) when VSXLEN=32.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vsstatusreg-rv32.edn[]

Virtual supervisor status register (vsstatus) when VSXLEN=64.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vsstatusreg.edn[]

The UXL field controls the effective XLEN for VU-mode, which may differ from the XLEN for VS-mode (VSXLEN). When VSXLEN=32, the UXL field does not exist, and VU-mode XLEN=32. When VSXLEN=64, UXL is a WARL field that is encoded the same as the MXL field of misa, shown in [misabase]. In particular, an implementation may make UXL be a read-only copy of field VSXL of hstatus, forcing VU-mode XLEN=VSXLEN.

If VSXLEN is changed from 32 to a wider width, and if field UXL is not restricted to a single value, it gets the value corresponding to the widest supported width not wider than the new VSXLEN.

When V=1, both vsstatus.FS and the HS-level sstatus.FS are in effect. Attempts to execute a floating-point instruction when either field is 0 (Off) raise an illegal-instruction exception. Modifying the floating-point state when V=1 causes both fields to be set to 3 (Dirty).

For a hypervisor to benefit from the extension context status, it must have its own copy in the HS-level sstatus, maintained independently of a guest OS running in VS-mode. While a version of the extension context status obviously must exist in vsstatus for VS-mode, a hypervisor cannot rely on this version being maintained correctly, given that VS-level software can change vsstatus.FS arbitrarily. If the HS-level sstatus.FS were not independently active and maintained by the hardware in parallel with vsstatus.FS while V=1, hypervisors would always be forced to conservatively swap all floating-point state when context-switching between virtual machines.

Similarly, when V=1, both vsstatus.VS and the HS-level sstatus.VS are in effect. Attempts to execute a vector instruction when either field is 0 (Off) raise an illegal-instruction exception. Modifying the vector state when V=1 causes both fields to be set to 3 (Dirty).

Read-only fields SD and XS summarize the extension context status as it is visible to VS-mode only. For example, the value of the HS-level sstatus.FS does not affect vsstatus.SD.

An implementation may make field UBE be a read-only copy of hstatus.VSBE.

When V=0, vsstatus does not directly affect the behavior of the machine, unless a virtual-machine load/store (HLV, HLVX, or HSV) or the MPRV feature in the mstatus register is used to execute a load or store as though V=1.

Virtual Supervisor Interrupt Registers (vsip and vsie)

The vsip and vsie registers are VSXLEN-bit read/write registers that are VS-mode’s versions of supervisor CSRs sip and sie, formatted as shown in Virtual supervisor interrupt-pending register (vsip). and Virtual supervisor interrupt-enable register (vsie). respectively. When V=1, vsip and vsie substitute for the usual sip and sie, so instructions that normally read or modify sip/sie actually access vsip/vsie instead. However, interrupts directed to HS-level continue to be indicated in the HS-level sip register, not in vsip, when V=1.

Virtual supervisor interrupt-pending register (vsip).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vsipreg.edn[]

Virtual supervisor interrupt-enable register (vsie).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vsiereg.edn[]

The standard portions (bits 15:0) of registers vsip and vsie are formatted as shown in Standard portion (bits 15:0) of vsip. and Standard portion (bits 15:0) of vsie. respectively.

Standard portion (bits 15:0) of vsip.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vsipreg-standard.edn[]

Standard portion (bits 15:0) of vsie.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vsiereg-standard.edn[]

When bit 13 of hideleg is zero, vsip.LCOFIP and vsie.LCOFIE are read-only zeros. Else, vsip.LCOFIP and vsie.LCOFIE are aliases of sip.LCOFIP and sie.LCOFIE.

The vsip.LCOFIP and vsie.LCOFIE bits were added in Version 1.13 of the Privileged Architecture.

When bit 10 of hideleg is zero, vsip.SEIP and vsie.SEIE are read-only zeros. Else, vsip.SEIP and vsie.SEIE are aliases of hip.VSEIP and hie.VSEIE.

When bit 6 of hideleg is zero, vsip.STIP and vsie.STIE are read-only zeros. Else, vsip.STIP and vsie.STIE are aliases of hip.VSTIP and hie.VSTIE.

When bit 2 of hideleg is zero, vsip.SSIP and vsie.SSIE are read-only zeros. Else, vsip.SSIP and vsie.SSIE are aliases of hip.VSSIP and hie.VSSIE.

Virtual Supervisor Trap Vector Base Address Register (vstvec)

The vstvec register is a VSXLEN-bit read/write register that is VS-mode’s version of supervisor register stvec, formatted as shown in Virtual supervisor trap vector base address register vstvec.. When V=1, vstvec substitutes for the usual stvec, so instructions that normally read or modify stvec actually access vstvec instead. When V=0, vstvec does not directly affect the behavior of the machine.

Virtual supervisor trap vector base address register vstvec.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vstvecreg.edn[]

Virtual Supervisor Scratch Register (vsscratch)

The vsscratch register is a VSXLEN-bit read/write register that is VS-mode’s version of supervisor register sscratch, formatted as shown in Virtual supervisor scratch register vsscratch.. When V=1, vsscratch substitutes for the usual sscratch, so instructions that normally read or modify sscratch actually access vsscratch instead. The contents of vsscratch never directly affect the behavior of the machine.

Virtual supervisor scratch register vsscratch.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vsscratchreg.edn[]

Virtual Supervisor Exception Program Counter (vsepc)

The vsepc register is a VSXLEN-bit read/write register that is VS-mode’s version of supervisor register sepc, formatted as shown in Virtual supervisor exception program counter (vsepc).. When V=1, vsepc substitutes for the usual sepc, so instructions that normally read or modify sepc actually access vsepc instead. When V=0, vsepc does not directly affect the behavior of the machine.

vsepc is a WARL register that must be able to hold the same set of values that sepc can hold.

Virtual supervisor exception program counter (vsepc).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vsepcreg.edn[]

Virtual Supervisor Cause Register (vscause)

The vscause register is a VSXLEN-bit read/write register that is VS-mode’s version of supervisor register scause, formatted as shown in Virtual supervisor cause register (vscause).. When V=1, vscause substitutes for the usual scause, so instructions that normally read or modify scause actually access vscause instead. When V=0, vscause does not directly affect the behavior of the machine.

vscause is a WLRL register that must be able to hold the same set of values that scause can hold.

Virtual supervisor cause register (vscause).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vscausereg.edn[]

Virtual Supervisor Trap Value Register (vstval)

The vstval register is a VSXLEN-bit read/write register that is VS-mode’s version of supervisor register stval, formatted as shown in Virtual supervisor trap value register (vstval).. When V=1, vstval substitutes for the usual stval, so instructions that normally read or modify stval actually access vstval instead. When V=0, vstval does not directly affect the behavior of the machine.

vstval is a WARL register that must be able to hold the same set of values that stval can hold.

Virtual supervisor trap value register (vstval).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/vstvalreg.edn[]

Virtual Supervisor Address Translation and Protection Register (vsatp)

The vsatp register is a VSXLEN-bit read/write register that is VS-mode’s version of supervisor register satp, formatted as shown in Virtual supervisor address translation and protection register vsatp when VSXLEN=32. for VSXLEN=32 and Virtual supervisor address translation and protection register vsatp when VSXLEN=64. for VSXLEN=64. When V=1, vsatp substitutes for the usual satp, so instructions that normally read or modify satp actually access vsatp instead. vsatp controls VS-stage address translation, the first stage of two-stage translation for guest virtual addresses (see Two-Stage Address Translation).

Virtual supervisor address translation and protection register vsatp when VSXLEN=32.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/rv32vsatpreg.edn[]

Virtual supervisor address translation and protection register vsatp when VSXLEN=64.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/rv64vsatpreg.edn[]

The vsatp register is considered active for the purposes of the address-translation algorithm unless the effective privilege mode is U and hstatus.HU=0. However, even when vsatp is active, VS-stage page-table entries’ A bits must not be set as a result of speculative execution, unless the effective privilege mode is VS or VU.

In particular, virtual-machine load/store (HLV, HLVX, or HSV) instructions that are misspeculatively executed must not cause VS-stage A bits to be set.

When V=0, a write to vsatp with an unsupported MODE value is either ignored as it is for satp, or the fields of vsatp are treated as WARL in the normal way. However, when V=1, a write to satp with an unsupported MODE value is ignored and no write to vsatp is effected.

When V=0, vsatp does not directly affect the behavior of the machine, unless a virtual-machine load/store (HLV, HLVX, or HSV) or the MPRV feature in the mstatus register is used to execute a load or store as though V=1.

Hypervisor Instructions

The hypervisor extension adds virtual-machine load and store instructions and two privileged fence instructions.

Hypervisor Virtual-Machine Load and Store Instructions

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/wavedrom/hypv-virt-load-and-store.edn[]

The hypervisor virtual-machine load and store instructions are valid only in M-mode or HS-mode, or in U-mode when hstatus.HU=1. Each instruction performs an explicit memory access as though V=1; i.e., with the address translation and protection, and the endianness, that apply to memory accesses in either VS-mode or VU-mode. Field SPVP of hstatus controls the privilege level of the access. The explicit memory access is done as though in VU-mode when SPVP=0, and as though in VS-mode when SPVP=1. As usual when V=1, two-stage address translation is applied, and the HS-level sstatus.SUM is ignored. HS-level sstatus.MXR makes execute-only pages readable for both stages of address translation (VS-stage and G-stage), whereas vsstatus.MXR affects only the first translation stage (VS-stage).

For every RV32I or RV64I load instruction, LB, LBU, LH, LHU, LW, LWU, and LD, there is a corresponding virtual-machine load instruction: HLV.B, HLV.BU, HLV.H, HLV.HU, HLV.W, HLV.WU, and HLV.D. For every RV32I or RV64I store instruction, SB, SH, SW, and SD, there is a corresponding virtual-machine store instruction: HSV.B, HSV.H, HSV.W, and HSV.D. Instructions HLV.WU, HLV.D, and HSV.D are not valid for RV32, of course.

Instructions HLVX.HU and HLVX.WU are the same as HLV.HU and HLV.WU, except that execute permission takes the place of read permission during address translation. That is, the memory being read must be executable in both stages of address translation, but read permission is not required. For the supervisor physical address that results from address translation, the supervisor physical memory attributes must grant both execute and read permissions. (The supervisor physical memory attributes are the machine’s physical memory attributes as modified by physical memory protection, [pmp], for supervisor level.)

HLVX cannot override machine-level physical memory protection (PMP), so attempting to read memory that PMP designates as execute-only still results in an access-fault exception.

Although HLVX instructions’ explicit memory accesses require execute permissions, they still raise the same exceptions as other load instructions, rather than raising fetch exceptions instead.

HLVX.WU is valid for RV32, even though LWU and HLV.WU are not. (For RV32, HLVX.WU can be considered a variant of HLV.W, as sign extension is irrelevant for 32-bit values.)

Attempts to execute a virtual-machine load/store instruction (HLV, HLVX, or HSV) when V=1 cause a virtual-instruction exception. Attempts to execute one of these same instructions from U-mode when hstatus.HU=0 cause an illegal-instruction exception.

Hypervisor Memory-Management Fence Instructions

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/wavedrom/hypv-mm-fence.edn[]

The hypervisor memory-management fence instructions, HFENCE.VVMA and HFENCE.GVMA, perform a function similar to SFENCE.VMA ([sfence.vma]), except applying to the VS-level memory-management data structures controlled by CSR vsatp (HFENCE.VVMA) or the guest-physical memory-management data structures controlled by CSR hgatp (HFENCE.GVMA). Instruction SFENCE.VMA applies only to the memory-management data structures controlled by the current satp (either the HS-level satp when V=0 or vsatp when V=1).

HFENCE.VVMA is valid only in M-mode or HS-mode. Its effect is much the same as temporarily entering VS-mode and executing SFENCE.VMA. Executing an HFENCE.VVMA guarantees that any previous stores already visible to the current hart are ordered before all implicit reads by that hart done for VS-stage address translation for instructions that

  • are subsequent to the HFENCE.VVMA, and

  • execute when hgatp.VMID has the same setting as it did when HFENCE.VVMA executed.

Implicit reads need not be ordered when hgatp.VMID is different than at the time HFENCE.VVMA executed. If operand rs1x0, it specifies a single guest virtual address, and if operand rs2x0, it specifies a single guest address-space identifier (ASID).

An HFENCE.VVMA instruction applies only to a single virtual machine, identified by the setting of hgatp.VMID when HFENCE.VVMA executes.

When rs2x0, bits XLEN-1:ASIDMAX of the value held in rs2 are reserved for future standard use. Until their use is defined by a standard extension, they should be zeroed by software and ignored by current implementations. Furthermore, if ASIDLEN < ASIDMAX, the implementation shall ignore bits ASIDMAX-1:ASIDLEN of the value held in rs2.

Simpler implementations of HFENCE.VVMA can ignore the guest virtual address in rs1 and the guest ASID value in rs2, as well as hgatp.VMID, and always perform a global fence for the VS-level memory management of all virtual machines, or even a global fence for all memory-management data structures.

Neither mstatus.TVM nor hstatus.VTVM causes HFENCE.VVMA to trap.

HFENCE.GVMA is valid only in HS-mode when mstatus.TVM=0, or in M-mode (irrespective of mstatus.TVM). Executing an HFENCE.GVMA instruction guarantees that any previous stores already visible to the current hart are ordered before all implicit reads by that hart done for G-stage address translation for instructions that follow the HFENCE.GVMA. If operand rs1x0, it specifies a single guest physical address, shifted right by 2 bits, and if operand rs2x0, it specifies a single virtual machine identifier (VMID).

Conceptually, an implementation might contain two address-translation caches: one that maps guest virtual addresses to guest physical addresses, and another that maps guest physical addresses to supervisor physical addresses. HFENCE.GVMA need not flush the former cache, but it must flush entries from the latter cache that match the HFENCE.GVMA’s address and VMID arguments.

More commonly, implementations contain address-translation caches that map guest virtual addresses directly to supervisor physical addresses, removing a level of indirection. For such implementations, any entry whose guest virtual address maps to a guest physical address that matches the HFENCE.GVMA’s address and VMID arguments must be flushed. Selectively flushing entries in this fashion requires tagging them with the guest physical address, which is costly, and so a common technique is to flush all entries that match the HFENCE.GVMA’s VMID argument, regardless of the address argument.


Like for a guest physical address written to htval on a trap, a guest physical address specified in rs1 is shifted right by 2 bits to accommodate addresses wider than the current XLEN.

When rs2x0, bits XLEN-1:VMIDMAX of the value held in rs2 are reserved for future standard use. Until their use is defined by a standard extension, they should be zeroed by software and ignored by current implementations. Furthermore, if VMIDLEN < VMIDMAX, the implementation shall ignore bits VMIDMAX-1:VMIDLEN of the value held in rs2.

Simpler implementations of HFENCE.GVMA can ignore the guest physical address in rs1 and the VMID value in rs2 and always perform a global fence for the guest-physical memory management of all virtual machines, or even a global fence for all memory-management data structures.

If hgatp.MODE is changed for a given VMID, an HFENCE.GVMA with rs1=x0 (and rs2 set to either x0 or the VMID) must be executed to order subsequent guest translations with the MODE change—even if the old MODE or new MODE is Bare.

Attempts to execute HFENCE.VVMA or HFENCE.GVMA when V=1 cause a virtual-instruction exception, while attempts to do the same in U-mode cause an illegal-instruction exception. Attempting to execute HFENCE.GVMA in HS-mode when mstatus.TVM=1 also causes an illegal-instruction exception.

Machine-Level CSRs

The hypervisor extension augments or modifies machine CSRs mstatus, mstatush, mideleg, mip, and mie, and adds CSRs mtval2 and mtinst.

Machine Status Registers (mstatus and mstatush)

The hypervisor extension adds two fields, MPV and GVA, to the machine-level mstatus or mstatush CSR, and modifies the behavior of several existing mstatus fields. Machine status register (mstatus) fpr RV64 when the hypervisor extension is implemented. shows the modified mstatus register when the hypervisor extension is implemented and MXLEN=64. When MXLEN=32, the hypervisor extension adds MPV and GVA not to mstatus but to mstatush. Additional machine status register (mstatush) for RV32 when the hypervisor extension is implemented. The format of mstatus is unchanged for RV32. shows the mstatush register when the hypervisor extension is implemented and MXLEN=32.

Machine status register (mstatus) fpr RV64 when the hypervisor extension is implemented.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hypv-mstatus.edn[]

Additional machine status register (mstatush) for RV32 when the hypervisor extension is implemented. The format of mstatus is unchanged for RV32.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hypv-mstatush.edn[]

The MPV bit (Machine Previous Virtualization Mode) is written by the implementation whenever a trap is taken into M-mode. Just as the MPP field is set to the (nominal) privilege mode at the time of the trap, the MPV bit is set to the value of the virtualization mode V at the time of the trap. When an MRET instruction is executed, the virtualization mode V is set to MPV, unless MPP=3, in which case V remains 0.

Field GVA (Guest Virtual Address) is written by the implementation whenever a trap is taken into M-mode. For any trap (breakpoint, address misaligned, access fault, page fault, or guest-page fault) that writes a guest virtual address to mtval, GVA is set to 1. For any other trap into M-mode, GVA is set to 0.

The TSR and TVM fields of mstatus affect execution only in HS-mode, not in VS-mode. The TW field affects execution in all modes except M-mode.

Setting TVM=1 prevents HS-mode from accessing hgatp or executing HFENCE.GVMA or HINVAL.GVMA, but has no effect on accesses to vsatp or instructions HFENCE.VVMA or HINVAL.VVMA.

TVM exists in mstatus to allow machine-level software to modify the address translations managed by a supervisor-level OS, usually for the purpose of inserting another stage of address translation below that controlled by the OS. The instruction traps enabled by TVM=1 permit machine level to co-opt both satp and hgatp and substitute shadow page tables that merge the OS’s chosen page translations with M-level’s lower-stage translations, all without the OS being aware. M-level software needs this ability not only to emulate the hypervisor extension if not already supported, but also to emulate any future RISC-V extensions that may modify or add address translation stages, perhaps, for example, to improve support for nested hypervisors, i.e., running hypervisors atop other hypervisors.

However, setting TVM=1 does not cause traps for accesses to vsatp or instructions HFENCE.VVMA or HINVAL.VVMA, or for any actions taken in VS-mode, because M-level software is not expected to need to involve itself in VS-stage address translation. For virtual machines, it should be sufficient, and in all likelihood faster as well, to leave VS-stage address translation alone and merge all other translation stages into G-stage shadow page tables controlled by hgatp. This assumption does place some constraints on possible future RISC-V extensions that current machines will be able to emulate efficiently.

The hypervisor extension changes the behavior of the Modify Privilege field, MPRV, of mstatus. When MPRV=0, translation and protection behave as normal. When MPRV=1, explicit memory accesses are translated and protected, and endianness is applied, as though the current virtualization mode were set to MPV and the current nominal privilege mode were set to MPP. Effect of MPRV on the translation and protection of explicit memory accesses. enumerates the cases.

Table 5. Effect of MPRV on the translation and protection of explicit memory accesses.
MPRV MPV MPP Effect

0

-

-

Normal access; current privilege mode applies.

1

0

0

U-level access with HS-level translation and protection only.

1

0

1

HS-level access with HS-level translation and protection only.

1

-

3

M-level access with no translation.

1

1

0

VU-level access with two-stage translation and protection. The HS-level MXR bit makes any executable page readable. vsstatus.MXR makes readable those pages marked executable at the VS translation stage, but only if readable at the guest-physical translation stage.

1

1

1

VS-level access with two-stage translation and protection. The HS-level MXR bit makes any executable page readable. vsstatus.MXR makes readable those pages marked executable at the VS translation stage, but only if readable at the guest-physical translation stage. vsstatus.SUM applies instead of the HS-level SUM bit.

MPRV does not affect the virtual-machine load/store instructions, HLV, HLVX, and HSV. The explicit loads and stores of these instructions always act as though V=1 and the nominal privilege mode were hstatus.SPVP, overriding MPRV.

The mstatus register is a superset of the HS-level sstatus register but is not a superset of vsstatus.

Machine Interrupt Delegation Register (mideleg)

When the hypervisor extension is implemented, bits 10, 6, and 2 of mideleg (corresponding to the standard VS-level interrupts) are each read-only one. Furthermore, if any guest external interrupts are implemented (GEILEN is nonzero), bit 12 of mideleg (corresponding to supervisor-level guest external interrupts) is also read-only one. VS-level interrupts and guest external interrupts are always delegated past M-mode to HS-mode.

For bits of mideleg that are zero, the corresponding bits in hideleg, hip, and hie are read-only zeros.

Machine Interrupt Registers (mip and mie)

The hypervisor extension gives registers mip and mie additional active bits for the hypervisor-added interrupts. Standard portion (bits 15:0) of mip. and Standard portion (bits 15:0) of mie. show the standard portions (bits 15:0) of registers mip and mie when the hypervisor extension is implemented.

Standard portion (bits 15:0) of mip.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hypv-mipreg-standard.edn[]

Standard portion (bits 15:0) of mie.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/hypv-miereg-standard.edn[]

Bits SGEIP, VSEIP, VSTIP, and VSSIP in mip are aliases for the same bits in hypervisor CSR hip, while SGEIE, VSEIE, VSTIE, and VSSIE in mie are aliases for the same bits in hie.

Machine Second Trap Value Register (mtval2)

The mtval2 register is an MXLEN-bit read/write register formatted as shown in Machine second trap value register (mtval2).. When a trap is taken into M-mode, mtval2 is written with additional exception-specific information, alongside mtval, to assist software in handling the trap.

Machine second trap value register (mtval2).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/mtval2reg.edn[]

When a guest-page-fault trap is taken into M-mode, mtval2 is written with either zero or the guest physical address that faulted, shifted right by 2 bits. For other traps, mtval2 is set to zero, but a future standard or extension may redefine mtval2’s setting for other traps.

If a guest-page fault is due to an implicit memory access during first-stage (VS-stage) address translation, a guest physical address written to mtval2 is that of the implicit memory access that faulted. Additional information is provided in CSR mtinst to disambiguate such situations.

Otherwise, for misaligned loads and stores that cause guest-page faults, a nonzero guest physical address in mtval2 corresponds to the faulting portion of the access as indicated by the virtual address in mtval. For instruction guest-page faults on systems with variable-length instructions, a nonzero mtval2 corresponds to the faulting portion of the instruction as indicated by the virtual address in mtval.

mtval2 is a WARL register that must be able to hold zero and may be capable of holding only an arbitrary subset of other 2-bit-shifted guest physical addresses, if any.

Machine Trap Instruction Register (mtinst)

The mtinst register is an MXLEN-bit read/write register formatted as shown in Machine trap instruction register (mtinst).. When a trap is taken into M-mode, mtinst is written with a value that, if nonzero, provides information about the instruction that trapped, to assist software in handling the trap. The values that may be written to mtinst on a trap are documented in Transformed Instruction or Pseudoinstruction for mtinst or htinst.

Machine trap instruction register (mtinst).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/mtinstreg.edn[]

mtinst is a WARL register that need only be able to hold the values that the implementation may automatically write to it on a trap.

Two-Stage Address Translation

Whenever the current virtualization mode V is 1, two-stage address translation and protection is in effect. For any virtual memory access, the original virtual address is converted in the first stage by VS-level address translation, as controlled by the vsatp register, into a guest physical address. The guest physical address is then converted in the second stage by guest physical address translation, as controlled by the hgatp register, into a supervisor physical address. The two stages are known also as VS-stage and G-stage translation. Although there is no option to disable two-stage address translation when V=1, either stage of translation can be effectively disabled by zeroing the corresponding vsatp or hgatp register.

The vsstatus field MXR, which makes execute-only pages readable, only overrides VS-stage page protection. Setting MXR at VS-level does not override guest-physical page protections. Setting MXR at HS-level, however, overrides both VS-stage and G-stage execute-only permissions.

When V=1, memory accesses that would normally bypass address translation are subject to G-stage address translation alone. This includes memory accesses made in support of VS-stage address translation, such as reads and writes of VS-level page tables.

Machine-level physical memory protection applies to supervisor physical addresses and is in effect regardless of virtualization mode.

Guest Physical Address Translation

The mapping of guest physical addresses to supervisor physical addresses is controlled by CSR hgatp (Hypervisor Guest Address Translation and Protection Register (hgatp)).

When the address translation scheme selected by the MODE field of hgatp is Bare, guest physical addresses are equal to supervisor physical addresses without modification, and no memory protection applies in the trivial translation of guest physical addresses to supervisor physical addresses.

When hgatp.MODE specifies a translation scheme of Sv32x4, Sv39x4, Sv48x4, or Sv57x4, G-stage address translation is a variation on the usual page-based virtual address translation scheme of Sv32, Sv39, Sv48, or Sv57, respectively. In each case, the size of the incoming address is widened by 2 bits (to 34, 41, 50, or 59 bits). To accommodate the 2 extra bits, the root page table (only) is expanded by a factor of four to be 16 KiB instead of the usual 4 KiB. Matching its larger size, the root page table also must be aligned to a 16 KiB boundary instead of the usual 4 KiB page boundary. Except as noted, all other aspects of Sv32, Sv39, Sv48, or Sv57 are adopted unchanged for G-stage translation. Non-root page tables and all page table entries (PTEs) have the same formats as documented in [sv32], [sv39], [sv48], and [sv57].

For Sv32x4, an incoming guest physical address is partitioned into a virtual page number (VPN) and page offset as shown in Sv32x4 virtual address (guest physical address).. This partitioning is identical to that for an Sv32 virtual address as depicted in [sv32va], except with 2 more bits at the high end in VPN[1]. (Note that the fields of a partitioned guest physical address also correspond one-for-one with the structure that Sv32 assigns to a physical address, depicted in [sv32va].)

Sv32x4 virtual address (guest physical address).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/sv32x4va.edn[]

For Sv39x4, an incoming guest physical address is partitioned as shown in Sv39x4 virtual address (guest physical address).. This partitioning is identical to that for an Sv39 virtual address as depicted in [sv39va], except with 2 more bits at the high end in VPN[2]. Address bits 63:41 must all be zeros, or else a guest-page-fault exception occurs.

Sv39x4 virtual address (guest physical address).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/sv39x4va.edn[]

For Sv48x4, an incoming guest physical address is partitioned as shown in Sv48x4 virtual address (guest physical address).. This partitioning is identical to that for an Sv48 virtual address as depicted in [sv48va], except with 2 more bits at the high end in VPN[3]. Address bits 63:50 must all be zeros, or else a guest-page-fault exception occurs.

Sv48x4 virtual address (guest physical address).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/sv48x4va.edn[]

For Sv57x4, an incoming guest physical address is partitioned as shown in Sv57x4 virtual address (guest physical address).. This partitioning is identical to that for an Sv57 virtual address as depicted in [sv57va], except with 2 more bits at the high end in VPN[4]. Address bits 63:59 must all be zeros, or else a guest-page-fault exception occurs.

Sv57x4 virtual address (guest physical address).

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/bytefield/sv57x4va.edn[]

The page-based G-stage address translation scheme for RV32, Sv32x4, is defined to support a 34-bit guest physical address so that an RV32 hypervisor need not be limited in its ability to virtualize real 32-bit RISC-V machines, even those with 33-bit or 34-bit physical addresses. This may include the possibility of a machine virtualizing itself, if it happens to use 33-bit or 34-bit physical addresses. Multiplying the size and alignment of the root page table by a factor of four is the cheapest way to extend Sv32 to cover a 34-bit address. The possible wastage of 12 KiB for an unnecessarily large root page table is expected to be of negligible consequence for most (maybe all) real uses.

A consistent ability to virtualize machines having as much as four times the physical address space as virtual address space is believed to be of some utility also for RV64. For a machine implementing 39-bit virtual addresses (Sv39), for example, this allows the hypervisor extension to support up to a 41-bit guest physical address space without either necessitating hardware support for 48-bit virtual addresses (Sv48) or falling back to emulating the larger address space using shadow page tables.

The conversion of an Sv32x4, Sv39x4, Sv48x4, or Sv57x4 guest physical address is accomplished with the same algorithm used for Sv32, Sv39, Sv48, or Sv57, as presented in [sv32algorithm], except that:

  • hgatp substitutes for the usual satp;

  • for the translation to begin, the effective privilege mode must be VS-mode or VU-mode;

  • when checking the U bit, the current privilege mode is always taken to be U-mode; and

  • guest-page-fault exceptions are raised instead of regular page-fault exceptions.

For G-stage address translation, all memory accesses (including those made to access data structures for VS-stage address translation) are considered to be user-level accesses, as though executed in U-mode. Access type permissions—readable, writable, or executable—are checked during G-stage translation the same as for VS-stage translation. For a memory access made to support VS-stage address translation (such as to read/write a VS-level page table), permissions and the need to set A and/or D bits at the G-stage level are checked as though for an implicit load or store, not for the original access type. However, any exception is always reported for the original access type (instruction, load, or store/AMO).

The G bit in all G-stage PTEs is reserved for future standard use. Until its use is defined by a standard extension, it should be cleared by software for forward compatibility, and must be ignored by hardware.

G-stage address translation uses the identical format for PTEs as regular address translation, even including the U bit, due to the possibility of sharing some (or all) page tables between G-stage translation and regular HS-level address translation. Regardless of whether this usage will ever become common, we chose not to preclude it.

Guest-Page Faults

Guest-page-fault traps may be delegated from M-mode to HS-mode under the control of CSR medeleg, but cannot be delegated to other privilege modes. On a guest-page fault, CSR mtval or stval is written with the faulting guest virtual address as usual, and mtval2 or htval is written either with zero or with the faulting guest physical address, shifted right by 2 bits. CSR mtinst or htinst may also be written with information about the faulting instruction or other reason for the access, as explained in Transformed Instruction or Pseudoinstruction for mtinst or htinst.

When an instruction fetch or a misaligned memory access straddles a page boundary, two different address translations are involved. When a guest-page fault occurs in such a circumstance, the faulting virtual address written to mtval/stval is the same as would be required for a regular page fault. Thus, the faulting virtual address may be a page-boundary address that is higher than the instruction’s original virtual address, if the byte at that page boundary is among the accessed bytes.

When a guest-page fault is not due to an implicit memory access for VS-stage address translation, a nonzero guest physical address written to mtval2/htval shall correspond to the exact virtual address written to mtval/stval.

Memory-Management Fences

The behavior of the SFENCE.VMA instruction is affected by the current virtualization mode V. When V=0, the virtual-address argument is an HS-level virtual address, and the ASID argument is an HS-level ASID. The instruction orders stores only to HS-level address-translation structures with subsequent HS-level address translations.

When V=1, the virtual-address argument to SFENCE.VMA is a guest virtual address within the current virtual machine, and the ASID argument is a VS-level ASID within the current virtual machine. The current virtual machine is identified by the VMID field of CSR hgatp, and the effective ASID can be considered to be the combination of this VMID with the VS-level ASID. The SFENCE.VMA instruction orders stores only to the VS-level address-translation structures with subsequent VS-stage address translations for the same virtual machine, i.e., only when hgatp.VMID is the same as when the SFENCE.VMA executed.

Hypervisor instructions HFENCE.VVMA and HFENCE.GVMA provide additional memory-management fences to complement SFENCE.VMA. These instructions are described in Hypervisor Memory-Management Fence Instructions.

[pmp-vmem] discusses the intersection between physical memory protection (PMP) and page-based address translation. It is noted there that, when PMP settings are modified in a manner that affects either the physical memory that holds page tables or the physical memory to which page tables point, M-mode software must synchronize the PMP settings with the virtual memory system. For HS-level address translation, this is accomplished by executing in M-mode an SFENCE.VMA instruction with rs1=x0 and rs2=x0, after the PMP CSRs are written. Synchronization with G-stage and VS-stage data structures is also needed. Executing an HFENCE.GVMA instruction with rs1=x0 and rs2=x0 suffices to flush all G-stage or VS-stage address-translation cache entries that have cached PMP settings corresponding to the final translated supervisor physical address. An HFENCE.VVMA instruction is not required.

Similarly, if the setting of the PBMTE bit in menvcfg is changed, an HFENCE.GVMA instruction with rs1=x0 and rs2=x0 suffices to synchronize with respect to the altered interpretation of G-stage and VS-stage PTEs' PBMT fields.

By contrast, if the PBMTE bit in henvcfg is changed, executing an HFENCE.VVMA with rs1=x0 and rs2=x0 suffices to synchronize with respect to the altered interpretation of VS-stage PTEs' PBMT fields for the currently active VMID.

No mechanism is provided to atomically change vsatp and hgatp together. Hence, to prevent speculative execution causing one guest’s VS-stage translations to be cached under another guest’s VMID, world-switch code should zero vsatp, then swap hgatp, then finally write the new vsatp value. Similarly, if henvcfg.PBMTE need be world-switched, it should be switched after zeroing vsatp but before writing the new vsatp value, obviating the need to execute an HFENCE.VVMA instruction.

Traps

Trap Cause Codes

The hypervisor extension augments the trap cause encoding. Machine and supervisor cause register (mcause and scause) values when the hypervisor extension is implemented. lists the possible M-mode and HS-mode trap cause codes when the hypervisor extension is implemented. Codes are added for VS-level interrupts (interrupts 2, 6, 10), for supervisor-level guest external interrupts (interrupt 12), for virtual-instruction exceptions (exception 22), and for guest-page faults (exceptions 20, 21, 23). Furthermore, environment calls from VS-mode are assigned cause 10, whereas those from HS-mode or S-mode use cause 9 as usual.

Table 6. Machine and supervisor cause register (mcause and scause) values when the hypervisor extension is implemented.
Interrupt Exception Code Description

1
1
1
1

0
1
2
3

Reserved
Supervisor software interrupt
Virtual supervisor software interrupt
Machine software interrupt

1
1
1
1

4
5
6
7

Reserved
Supervisor timer interrupt
Virtual supervisor timer interrupt
Machine timer interrupt

1
1
1
1

8
9
10
11

Reserved
Supervisor external interrupt
Virtual supervisor external interrupt
Machine external interrupt

1
1
1
1

12
13
14-15
≥16

Supervisor guest external interrupt
Reserved for counter-overflow interrupt
Reserved
Designated for platform use

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16-19
20
21
22
23
24-31
32-47
48-63
≥64

Instruction address misaligned
Instruction access fault
Illegal instruction
Breakpoint
Load address misaligned
Load access fault
Store/AMO address misaligned
Store/AMO access fault
Environment call from U-mode or VU-mode
Environment call from HS-mode
Environment call from VS-mode
Environment call from M-mode
Instruction page fault
Load page fault
Reserved
Store/AMO page fault
Reserved
Instruction guest-page fault
Load guest-page fault
Virtual instruction
Store/AMO guest-page fault
Designated for custom use
Reserved
Designated for custom use
Reserved

HS-mode and VS-mode ECALLs use different cause values so they can be delegated separately.

When V=1, a virtual-instruction exception (code 22) is normally raised instead of an illegal-instruction exception if the attempted instruction is HS-qualified but is prevented from executing when V=1 either due to insufficient privilege or because the instruction is expressly disabled by a supervisor or hypervisor CSR such as scounteren or hcounteren. An instruction is HS-qualified if it would be valid to execute in HS-mode (for some values of the instruction’s register operands), assuming fields TSR and TVM of CSR mstatus are both zero.

A special rule applies for CSR instructions that access 32-bit high-half CSRs such as cycleh and htimedeltah. When V=1 and XLEN=32, an invalid attempt to access a high-half CSR raises a virtual-instruction exception instead of an illegal-instruction exception if the same CSR instruction for the corresponding low-half CSR (e.g.cycle or htimedelta) is HS-qualified.

When XLEN>32, an attempt to access a high-half CSR always raises an illegal-instruction exception.

Specifically, a virtual-instruction exception is raised for the following cases:

  • in VS-mode, attempts to access a non-high-half counter CSR when the corresponding bit in hcounteren is 0 and the same bit in mcounteren is 1;

  • in VS-mode, if XLEN=32, attempts to access a high-half counter CSR when the corresponding bit in hcounteren is 0 and the same bit in mcounteren is 1;

  • in VU-mode, attempts to access a non-high-half counter CSR when the corresponding bit in either hcounteren or scounteren is 0 and the same bit in mcounteren is 1;

  • in VU-mode, if XLEN=32, attempts to access a high-half counter CSR when the corresponding bit in either hcounteren or scounteren is 0 and the same bit in mcounteren is 1;

  • in VS-mode or VU-mode, attempts to execute a hypervisor instruction (HLV, HLVX, HSV, or HFENCE);

  • in VS-mode or VU-mode, attempts to access an implemented non-high-half hypervisor CSR or VS CSR when the same access (read/write) would be allowed in HS-mode, assuming mstatus.TVM=0;

  • in VS-mode or VU-mode, if XLEN=32, attempts to access an implemented high-half hypervisor CSR or high-half VS CSR when the same access (read/write) to the CSR"s low-half partner would be allowed in HS-mode, assuming mstatus.TVM=0;

  • in VU-mode, attempts to execute WFI when mstatus.TW=0, or to execute a supervisor instruction (SRET or SFENCE);

  • in VU-mode, attempts to access an implemented non-high-half supervisor CSR when the same access (read/write) would be allowed in HS-mode, assuming mstatus.TVM=0;

  • in VU-mode, if XLEN=32, attempts to access an implemented high-half supervisor CSR when the same access to the CSR’s low-half partner would be allowed in HS-mode, assuming mstatus.TVM=0;

  • in VS-mode, attempts to execute WFI when hstatus.VTW=1 and mstatus.TW=0, unless the instruction completes within an implementation-specific, bounded time;

  • in VS-mode, attempts to execute SRET when hstatus.VTSR=1; and

  • in VS-mode, attempts to execute an SFENCE.VMA or SINVAL.VMA instruction or to access satp, when hstatus.VTVM=1.

Other extensions to the RISC-V Privileged Architecture may add to the set of circumstances that cause a virtual-instruction exception when V=1.

On a virtual-instruction trap, mtval or stval is written the same as for an illegal-instruction trap.

It is not unusual that hypervisors must emulate the instructions that raise virtual-instruction exceptions, to support nested hypervisors or for other reasons. Machine level is expected ordinarily to delegate virtual-instruction traps directly to HS-level, whereas illegal-instruction traps are likely to be processed first in M-mode before being conditionally delegated (by software) to HS-level. Consequently, virtual-instruction traps are expected typically to be handled faster than illegal-instruction traps.

When not emulating the trapping instruction, a hypervisor should convert a virtual-instruction trap into an illegal-instruction exception for the guest virtual machine.


Because TSR and TVM in mstatus are intended to impact only S-mode (HS-mode), they are ignored for determining exceptions in VS-mode.

Table 7. Synchronous exception priority when the hypervisor extension is implemented.
Priority Exc.Code Description

Highest

3

Instruction address breakpoint

12, 20, 1

During instruction address translation:
   First encountered page fault, guest-page fault, or access fault

1

With physical address for instruction:
   Instruction access fault

2
22
0
8, 9, 10, 11
3
3

Illegal instruction
Virtual instruction
Instruction address misaligned
Environment call
Environment break
   Load/store/AMO address breakpoint

4,6

Optionally:
   Load/store/AMO address misaligned

13, 15, 21, 23, 5, 7

During address translation for an explicit memory access:
   First encountered page fault, guest-page fault, or access fault

5, 7

With physical address for an explicit memory access:
   Load/store/AMO access fault

Lowest

4, 6

If not higher priority:
   Load/store/AMO address misaligned

If an instruction may raise multiple synchronous exceptions, the decreasing priority order of Synchronous exception priority when the hypervisor extension is implemented. indicates which exception is taken and reported in mcause or scause.

Trap Entry

When a trap occurs in HS-mode or U-mode, it goes to M-mode, unless delegated by medeleg or mideleg, in which case it goes to HS-mode. When a trap occurs in VS-mode or VU-mode, it goes to M-mode, unless delegated by medeleg or mideleg, in which case it goes to HS-mode, unless further delegated by hedeleg or hideleg, in which case it goes to VS-mode.

When a trap is taken into M-mode, virtualization mode V gets set to 0, and fields MPV and MPP in mstatus (or mstatush) are set according to Value of mstatus/mstatush fields MPV and MPP after a trap into M-mode. Upon trap return, MPV is ignored when MPP=3.. A trap into M-mode also writes fields GVA, MPIE, and MIE in mstatus/mstatush and writes CSRs mepc, mcause, mtval, mtval2, and mtinst.

Table 8. Value of mstatus/mstatush fields MPV and MPP after a trap into M-mode. Upon trap return, MPV is ignored when MPP=3.
Previous Mode MPV MPP

U-mode
HS-mode
M-mode

0
0
0

0
1
3

VU-mode
VS-mode

1
1

0
1

When a trap is taken into HS-mode, virtualization mode V is set to 0, and hstatus.SPV and sstatus.SPP are set according to Value of hstatus field SPV and sstatus field SPP after a trap into HS-mode.. If V was 1 before the trap, field SPVP in hstatus is set the same as sstatus.SPP; otherwise, SPVP is left unchanged. A trap into HS-mode also writes field GVA in hstatus, fields SPIE and SIE in sstatus, and CSRs sepc, scause, stval, htval, and htinst.

Table 9. Value of hstatus field SPV and sstatus field SPP after a trap into HS-mode.
Previous Mode SPV SPP

U-mode
HS-mode

0
0

0
1

VU-mode
VS-mode

1
1

0
1

When a trap is taken into VS-mode, vsstatus.SPP is set according to Value of vsstatus field SPP after a trap into VS-mode.. Register hstatus and the HS-level sstatus are not modified, and the virtualization mode V remains 1. A trap into VS-mode also writes fields SPIE and SIE in vsstatus and writes CSRs vsepc, vscause, and vstval.

Table 10. Value of vsstatus field SPP after a trap into VS-mode.
Previous Mode SPP

VU-mode
VS-mode

0
1

Transformed Instruction or Pseudoinstruction for mtinst or htinst

On any trap into M-mode or HS-mode, one of these values is written automatically into the appropriate trap instruction CSR, mtinst or htinst:

  • zero;

  • a transformation of the trapping instruction;

  • a custom value (allowed only if the trapping instruction is non-standard); or

  • a special pseudoinstruction.

Except when a pseudoinstruction value is required (described later), the value written to mtinst or htinst may always be zero, indicating that the hardware is providing no information in the register for this particular trap.

The value written to the trap instruction CSR serves two purposes. The first is to improve the speed of instruction emulation in a trap handler, partly by allowing the handler to skip loading the trapping instruction from memory, and partly by obviating some of the work of decoding and executing the instruction. The second purpose is to supply, via pseudoinstructions, additional information about guest-page-fault exceptions caused by implicit memory accesses done for VS-stage address translation.

A transformation of the trapping instruction is written instead of simply a copy of the original instruction in order to minimize the burden for hardware yet still provide to a trap handler the information needed to emulate the instruction. An implementation may at any time reduce its effort by substituting zero in place of the transformed instruction.

On an interrupt, the value written to the trap instruction register is always zero. On a synchronous exception, if a nonzero value is written, one of the following shall be true about the value:

  • Bit 0 is 1, and replacing bit 1 with 1 makes the value into a valid encoding of a standard instruction.

    In this case, the instruction that trapped is the same kind as indicated by the register value, and the register value is the transformation of the trapping instruction, as defined later. For example, if bits 1:0 are binary 11 and the register value is the encoding of a standard LW (load word) instruction, then the trapping instruction is LW, and the register value is the transformation of the trapping LW instruction.

  • Bit 0 is 1, and replacing bit 1 with 1 makes the value into an instruction encoding that is explicitly designated for a custom instruction (not an unused reserved encoding).

    This is a custom value. The instruction that trapped is a non-standard instruction. The interpretation of a custom value is not otherwise specified by this standard.

  • The value is one of the special pseudoinstructions defined later, all of which have bits 1:0 equal to 00.

These three cases exclude a large number of other possible values, such as all those having bits 1:0 equal to binary 10. A future standard or extension may define additional cases, thus allowing values that are currently excluded. Software may safely treat an unrecognized value in a trap instruction register the same as zero.

To be forward-compatible with future revisions of this standard, software that interprets a nonzero value from mtinst or htinst must fully verify that the value conforms to one of the cases listed above. For instance, for RV64, discovering that bits 6:0 of mtinst are 0000011 and bits 14:12 are 010 is not sufficient to establish that the first case applies and the trapping instruction is a standard LW instruction; rather, software must also confirm that bits 63:32 of mtinst are all zeros. A future standard might define new values for 64-bit mtinst that are nonzero in bits 63:32 yet may coincidentally have in bits 31:0 the same bit patterns as standard RV64 instructions.


Unlike for standard instructions, there is no requirement that the instruction encoding of a custom value be of the same ``kind'' as the instruction that trapped (or even have any correlation with the trapping instruction).

Values that may be automatically written to the trap instruction register (mtinst or htinst) on an exception trap. shows the values that may be automatically written to the trap instruction register for each standard exception cause. For exceptions that prevent the fetching of an instruction, only zero or a pseudoinstruction value may be written. A custom value may be automatically written only if the instruction that traps is non-standard. A future standard or extension may permit other values to be written, chosen from the set of allowed values established earlier.

Table 11. Values that may be automatically written to the trap instruction register (mtinst or htinst) on an exception trap.
Exception Zero Transformed
Standard
Instruction
Custom Value Pseudo-instruction Value

Instruction address misaligned

Yes

No

Yes

No

Instruction access fault
Illegal instruction
Breakpoint
Virtual instruction

Yes
Yes
Yes
Yes

No
No
No
No

No
No
Yes
Yes

No
No
No
No

Load address misaligned
Load access fault
Store/AMO address misaligned
Store/AMO access fault

Yes
Yes
Yes
Yes

Yes
Yes
Yes
Yes

Yes
Yes
Yes
Yes

No
No
No
No

Environment call

Yes

No

Yes

No

Instruction page fault
Load page fault
Store/AMO page fault

Yes
Yes
Yes

No
Yes
Yes

No
Yes
Yes

No
No
No

Instruction guest-page fault
Load guest-page fault
Store/AMO guest-page fault

Yes
Yes
Yes

No
Yes
Yes

No
Yes
Yes

Yes
Yes
Yes

As enumerated in the table, a synchronous exception may write to the trap instruction register a standard transformation of the trapping instruction only for exceptions that arise from explicit memory accesses (from loads, stores, and AMO instructions). Accordingly, standard transformations are currently defined only for these memory-access instructions. If a synchronous trap occurs for a standard instruction for which no transformation has been defined, the trap instruction register shall be written with zero (or, under certain circumstances, with a special pseudoinstruction value).

For a standard load instruction that is not a compressed instruction and is one of LB, LBU, LH, LHU, LW, LWU, LD, FLW, FLD, FLQ, or FLH, the transformed instruction has the format shown in Transformed noncompressed load instruction (LB, LBU, LH, LHU, LW, LWU, LD, FLW, FLD, FLQ, or FLH). Fields funct3, rd, and opcode are the same as the trapping load instruction..

Transformed noncompressed load instruction (LB, LBU, LH, LHU, LW, LWU, LD, FLW, FLD, FLQ, or FLH). Fields funct3, rd, and opcode are the same as the trapping load instruction.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/wavedrom/transformedloadinst.edn[]

For a standard store instruction that is not a compressed instruction and is one of SB, SH, SW, SD, FSW, FSD, FSQ, or FSH, the transformed instruction has the format shown in Transformed noncompressed store instruction (SB, SH, SW, SD, FSW, FSD, FSQ, or FSH). Fields rs2, funct3, and opcode are the same as the trapping store instruction..

Transformed noncompressed store instruction (SB, SH, SW, SD, FSW, FSD, FSQ, or FSH). Fields rs2, funct3, and opcode are the same as the trapping store instruction.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/wavedrom/transformedstoreinst.edn[]

For a standard atomic instruction (load-reserved, store-conditional, or AMO instruction), the transformed instruction has the format shown in Transformed atomic instruction (load-reserved, store-conditional, or AMO instruc-tion). All fields are the same as the trapping instruction except bits 19:15, Addr. Offset..

Transformed atomic instruction (load-reserved, store-conditional, or AMO instruc-tion). All fields are the same as the trapping instruction except bits 19:15, Addr. Offset.

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/wavedrom/transformedatomicinst.edn[]

For a standard virtual-machine load/store instruction (HLV, HLVX, or HSV), the transformed instruction has the format shown in Transformed virtual-machine load/store instruction (HLV, HLVX, HSV). All fields are the same as the trapping instruction except bits 19:15, Addr. Offset.

Transformed virtual-machine load/store instruction (HLV, HLVX, HSV). All fields are the same as the trapping instruction except bits 19:15, Addr. Offset

Unresolved include directive in modules/chapters/pages/hypervisor.adoc - include::images/wavedrom/transformedvmaccessinst.edn[]

In all the transformed instructions above, the Addr. Offset field that replaces the instruction’s rs1 field in bits 19:15 is the positive difference between the faulting virtual address (written to mtval or stval) and the original virtual address. This difference can be nonzero only for a misaligned memory access. Note also that, for basic loads and stores, the transformations replace the instruction’s immediate offset fields with zero.

For a standard compressed instruction (16-bit size), the transformed instruction is found as follows:

  1. Expand the compressed instruction to its 32-bit equivalent.

  2. Transform the 32-bit equivalent instruction.

  3. Replace bit 1 with a 0.

Bits 1:0 of a transformed standard instruction will be binary 01 if the trapping instruction is compressed and 11 if not.

In decoding the contents of mtinst or htinst, once software has determined that the register contains the encoding of a standard basic load (LB, LBU, LH, LHU, LW, LWU, LD, FLW, FLD, FLQ, or FLH) or basic store (SB, SH, SW, SD, FSW, FSD, FSQ, or FSH), it is not necessary to confirm also that the immediate offset fields (31:25, and 24:20 or 11:7) are zeros. The knowledge that the register’s value is the encoding of a basic load/store is sufficient to prove that the trapping instruction is of the same kind.

A future version of this standard may add information to the fields that are currently zeros. However, for backwards compatibility, any such information will be for performance purposes only and can safely be ignored.

For guest-page faults, the trap instruction register is written with a special pseudoinstruction value if: (a) the fault is caused by an implicit memory access for VS-stage address translation, and (b) a nonzero value (the faulting guest physical address) is written to mtval2 or htval. If both conditions are met, the value written to mtinst or htinst must be taken from Special pseudoinstruction values for guest-page faults. The RV32 values are used when VSXLEN=32, and the RV64 values when VSXLEN=64.; zero is not allowed.

Table 12. Special pseudoinstruction values for guest-page faults. The RV32 values are used when VSXLEN=32, and the RV64 values when VSXLEN=64.
Value Meaning

0x00002000
0x00002020

32-bit read for VS-stage address translation (RV32)
32-bit write for VS-stage address translation (RV32)

0x00003000
0x00003020

64-bit read for VS-stage address translation (RV64)
64-bit write for VS-stage address translation (RV64)

The defined pseudoinstruction values are designed to correspond closely with the encodings of basic loads and stores, as illustrated by Standard instructions corresponding to the special psudoinstructions of [pseudoinsts]..

Table 13. Standard instructions corresponding to the special psudoinstructions of [pseudoinsts].
Encoding Instruction

0x00002003
0x00002023

lw x0,0(x0)
sw x0,0(x0)

0x00003003
0x00003023

ld x0,0(x0)
sd x0,0(x0)

A write pseudoinstruction (0x00002020 or 0x00003020) is used for the case that the machine is attempting automatically to update bits A and/or D in VS-level page tables. All other implicit memory accesses for VS-stage address translation will be reads. If a machine never automatically updates bits A or D in VS-level page tables (leaving this to software), the write case will never arise. The fact that such a page table update must actually be atomic, not just a simple write, is ignored for the pseudoinstruction.

If the conditions that necessitate a pseudoinstruction value can ever occur for M-mode, then mtinst cannot be entirely read-only zero; and likewise for HS-mode and htinst. However, in that case, the trap instruction registers may minimally support only values 0 and 0x00002000 or 0x00003000, and possibly 0x00002020 or 0x00003020, requiring as few as one or two flip-flops in hardware, per register.


There is no harm here in ignoring the atomicity requirement for page table updates, because a hypervisor is not expected in these circumstances to emulate an implicit memory access that fails. Rather, the hypervisor is given enough information about the faulting access to be able to make the memory accessible (e.g. by restoring a missing page of virtual memory) before resuming execution by retrying the faulting instruction.

Trap Return

The MRET instruction is used to return from a trap taken into M-mode. MRET first determines what the new privilege mode will be according to the values of MPP and MPV in mstatus or mstatush, as encoded in Value of mstatus/mstatush fields MPV and MPP after a trap into M-mode. Upon trap return, MPV is ignored when MPP=3.. MRET then in mstatus/mstatush sets MPV=0, MPP=0, MIE=MPIE, and MPIE=1. Lastly, MRET sets the privilege mode as previously determined, and sets pc=mepc.

The SRET instruction is used to return from a trap taken into HS-mode or VS-mode. Its behavior depends on the current virtualization mode.

When executed in M-mode or HS-mode (i.e., V=0), SRET first determines what the new privilege mode will be according to the values in hstatus.SPV and sstatus.SPP, as encoded in Value of hstatus field SPV and sstatus field SPP after a trap into HS-mode.. SRET then sets hstatus.SPV=0, and in sstatus sets SPP=0, SIE=SPIE, and SPIE=1. Lastly, SRET sets the privilege mode as previously determined, and sets pc=sepc.

When executed in VS-mode (i.e., V=1), SRET sets the privilege mode according to Value of vsstatus field SPP after a trap into VS-mode., in vsstatus sets SPP=0, SIE=SPIE, and SPIE=1, and lastly sets pc=vsepc.